Isthmus Models

Cable for Networking two EOS0610i Chargers Together, for balance charging or balancing two separate packs to be wired in series as one 4S to 12S pack.

Harness to fit between HP-TI-PRGUSB USB-to-Serial Adapter and EOS0606i Series Chargers, for PC Connections
To connect a Hyperion Balance Charger with Data Port to PC, you will need:

* This Harness, HP-EOS0606-PCCBL
* HP-TI-PRGUSB USB-to-Serial Adapter

Once Connected to PC, these functions would be available
Chargers EOS0606i DC and EOS0606i AC/DC
- PC Logging
Software

Replacement clips for EOS NET and DUO chargers. Clips have 4mm female gold sockets, and Male connectors and shrink tube are included to allow upgrade of budget chargers with fixed clips.

Harness to fit between HP-TI-PRGUSB USB-to-Serial Adapter and EOS06xx Series Chargers, for PC Connections
To connect a Hyperion Balance Charger with Data Port to PC, you will need:
* This Harness, HP-EOS06-PCCBL
* HP-TI-PRGUSB USB-to-Serial Adapter

 
Once Connected to PC, these functions would be available
Chargers EOS0610i NET and EOS0610i DUO
- Firmware Upgrades (see 0610i upgrade manual for connection details)
- PC Logging Software (PC soft avail about May 1st 2008)
Chargers EOS0606i DC and EOS0606i AC/DC
- PC Logging Software (PC soft avail about June 1st 2008)

NEW! DIRECT USB Adapter for Programming Hyperion TITAN Brushless ESC via PC, or Connection of Emeter to PC Graphing Software or firmware upgrade
Click here to see DataSheet for full details, TITAN PC Software Download, Drivers, and more...

TempSensor for any Hyperion Charger with a Temp Sensor Port

EOS Output Harness for Balance Charging 2S Car Packs such as ORION, TRAKPOWER and CHECKPOINT.

Fits EOS balance Chargers (EOS0403i, 0606i-x, 0610i-x) and LBA10. Battery-side has 4mm main bullet connectors, plus 2mm bullet for balance port on battery. SEE DIAGRAM HERE.

Because long wires and extra connectors in the balance circuit can potentially reduce accuracy of charging and balancing, this harness in made to connect directly to the Balance Port on Hyperion balance chargers (as seen in this picture). However, if you prefer (or need the extra length) you may use the Hyperion multi-adapter which came with your EOS charger and plug the HP-LB10-CAR balance connector into the 6S port on the Hyperion multi-adapter.

If you have a charger which can charge 3.7v LiPo batteries, but does not have a balancer built in, you can use a Hyperion LBA10 Balancer between your charger and the EOSOUT-CAR02 harness, to balance charge your 2S Car pack.

NEW! Multi-Adapter Balancer Harnesses for EOS LBA10 and Hyperion Balance Chargers, 2S to 6S via one Harness! Available in Versions for All Lipoly Pack Major Brands

NEW VERSION DOES NOT INCLUDE CABLE. ONLY MULTI ADAPTER BOARD. USE CABLE THAT WAS SUPPLIED WITH MULTI ADAPTERS THAT CAME WITH THE CHARGER NOTE: These cables are NOT included with the Hyperion 1210I charger!
IF YOUR CHARGER DID NOT COME WITH A MULTI ADAPTER YOU WILL NEED THE HYPERION MULTI-ADAPTER EXTENDER HP-LB10-EXT

This longer extender cable allows your 2-6s batteries to connect to all Hyperion EOS Chargers via Hyperion Multi-Adapters.


These have a wire length between the connectors of 14.5cm, which is 5.5cm (a little more than 2") longer than the old version included with earlier Hyperion chargers. Newer-production chargers already include this longer cable, so check the length of your existing cable before ordering this item.

NEW! Multi-Adapter Balancer Harnesses for EOS LBA10 and Hyperion Balance Chargers, 2S to 6S via one Harness! Available in Versions for All Lipoly Pack Major Brands

NEW VERSION DOES NOT INCLUDE CABLE. ONLY MULTI ADAPTER BOARD. USE CABLE THAT WAS SUPPLIED WITH MULTI ADAPTERS THAT CAME WITH THE CHARGER NOTE: These cables are NOT included with the Hyperion 1210I charger!
IF YOUR CHARGER DID NOT COME WITH A MULTI ADAPTER YOU WILL NEED THE HYPERION MULTI-ADAPTER EXTENDER HP-LB10-EXT

NEW! Multi-Adapter Balancer Harnesses for EOS LBA10 and Hyperion Balance Chargers, 2S to 6S via one Harness! Available in Versions for All Lipoly Pack Major Brands

NEW VERSION DOES NOT INCLUDE CABLE. ONLY MULTI ADAPTER BOARD. USE CABLE THAT WAS SUPPLIED WITH MULTI ADAPTERS THAT CAME WITH THE CHARGER NOTE: These cables are NOT included with the Hyperion 1210I charger!
IF YOUR CHARGER DID NOT COME WITH A MULTI ADAPTER YOU WILL NEED THE HYPERION MULTI-ADAPTER EXTENDER HP-LB10-EXT

NEW! Multi-Adapter Balancer Harnesses for EOS LBA10 and Hyperion Balance Chargers, 2S to 6S via one Harness! Available in Versions for All Lipoly Pack Major Brands

NEW VERSION DOES NOT INCLUDE CABLE. ONLY MULTI ADAPTER BOARD. USE CABLE THAT WAS SUPPLIED WITH MULTI ADAPTERS THAT CAME WITH THE CHARGER NOTE: These cables are NOT included with the Hyperion 1210I charger!
IF YOUR CHARGER DID NOT COME WITH A MULTI ADAPTER YOU WILL NEED THE HYPERION MULTI-ADAPTER EXTENDER HP-LB10-EXT

NEW! Multi-Adapter Balancer Harnesses for EOS LBA10 and Hyperion Balance Chargers, 2S to 6S via one Harness! Available in Versions for All Lipoly Pack Major Brands

NEW VERSION DOES NOT INCLUDE CABLE. ONLY MULTI ADAPTER BOARD. USE CABLE THAT WAS SUPPLIED WITH MULTI ADAPTERS THAT CAME WITH THE CHARGER NOTE: These cables are NOT included with the Hyperion 1210I charger!
IF YOUR CHARGER DID NOT COME WITH A MULTI ADAPTER YOU WILL NEED THE HYPERION MULTI-ADAPTER EXTENDER HP-LB10-EXT

NEW! Balancer Multi-Adapter for EOS0720iNET Balance Chargers. This is the 2S to 7S Board ONLY. Available in Versions for All Lipoly Pack Major Brands SEE DETAILS for APPLICATIONS

EOS720i/730i ONLY

Applications list below may be subject to change, depending on maker decisions outside our control. If you successfully use one of our adapters with a brand not listed below, please email sales@hyperion.hk to let them know, so the information can be made available to users worldwide.



Tech Note*: Due to a non-standard wiring arrangement on Thunderpower and FlightPower 4S packs only, the 4S packs may need the 6th wire removed in order to function properly with HP-EOSLBA-26TP MultiAdapter for 4S charging. SEE DIAGRAM HERE

7-pin MALE type connector. 100mm Lead - Fits Socket in LBA 10 Unit

If you have a lithium pack other than PolyQuest, Hyperion, or the newer E-Tec (these are all compatible with LBA 10 already), and you have the mating balance adapter for that pack (example, the connector that comes with ThunderPower balancers) you can use this to make your pack compatible with the EOS LBA 10.

To see the LBA 10 CLICK HERE

WARNING: DOES NOT FIT LBA 6

DataPort Cable for connecting LBA10 Balancer to compatible Hyperion Chargers, in order to view individual cell voltages during the charge process

Set for Networking two LBA10 Balancers together, for balance charging two packs as one 7S to 12S pack. Includes Network Cable (for NET PORT) and one 4mm Female-Female adapter to serial-connect LBA10 Input leads together.
The LBA10 Balancer user's manual explains how to use this cable and connector set, in order to balance charge two packs of same make and capacity as if they were a single pack, using two LBA10 networked together in Master-Slave modes. After such balance charging, you may safely connect the two packs together in Serial or Parallel as you wish. (for example, two packs of Hyperion LVX-5000-4S, connected in series after balance charging to make an 8S 5000mAh pack)

NEW! Harnesses to fit between HP-EOSLBA-7Uxx Multi-Adapters and EOS 0720i/730I Balance Chargers

The Hobby People Battery Safety Bag is designed for use with Li-PO batteries when charging, storing, or transporting. The added power of Li-PO batteries is utilized through stronger chemical reactions, making them more volatile. When these batteries are punctured or damaged in any way combustion may occur. Safety bags help to prevent any mishaps.